CD3-JIVE
Advanced 6U Dual Screen CompactPCI CPU
Scalable from 1GHz Ultra Low Voltage Celeron® M to 2.0GHz Pentium® M
Alternatively equipped with the Intel® series of (LV) Pentium® M and (ULV) Celeron® M
processors and up to 2GB RAM, the CD3-JIVE is a versatile 4HP/6U
(double size Eurocard)
CompactPCI®
CPU board, designed especially for systems
which require high performance at low power consumption.
Available with a variety of processors, the CD3-JIVE covers
a wide range of industrial applications.
The chipset is based on PCI Express technology and has a powerful integrated
graphics accelerator. The CD3-JIVE is provided with two independent DVI video
connectors for attachment of one or two displays. If both video ports are active
in single-channel mode, they can have different display timing and data.
Alternatively the DVI ports can be combined for a dual screen configuration,
supporting higher resolutions and refresh rates.
|
|
The CD3-JIVE is equipped with three independent Gigabit Ethernet controllers
(including PICMG 2.16 support), and eight USB 2.0 ports for high speed communication.
An on-board socket accommodates either a CompactFlash card, or an 1.8-inch hard
disk module.
Typically, the PMC mezzanine module connector will be used for individual
system expansion. As an option, the CD3-JIVE is also available with a dual
2.5-inch SATA hard disk add-on module, which occupies the PMC slot.
Furthermore, a rear I/O transition module is available for the CD3-JIVE. Four
Serial ATA channels are routed across the J3-J5 CPCI connectors, besides two
Gigabit Ethernet ports, four USB channels and a variety of other useful signals.
|
|
CD3-JIVE - Dual Screen DVI Video & Dual SATA Drives on-Board (Option)
|
|
CD3-JIVE with CDT-RIO Rear I/O Transition Module (Option)
|
|
CDT-RIO Rear I/O Transition Module (Option)
|
|
CD3-JIVE 8HP Front Panel Solution with PMC Module, C14-SATA, CCA-LAMBADA
|
|
Feature Summary CD3-JIVE
|
|
Form Factor
|
CompactPCI Double size CompactPCI style Eurocard (160x233mm2),
front panel width 4HP (20.3mm)
|
|
Processor
|
Designed for Intel® Pentium® M Micro FC-BGA 479 processors
(90nm Dothan),
maximum junction temperature 100°C
- CD3-2: 1.0GHz ULV Celeron® M (Dothan 373), 400MHz FSB, 512KB L2 cache, 5W
- CD3-3: 1.4GHz LV Pentium® M (Dothan 738), 400MHz FSB, 2MB L2 cache, 10W
- CD3-6: 2.0GHz Pentium® M (Dothan 760), 533MHz FSB, 2MB L2 cache, 27W
|
|
Chipset
|
Intel® i915 (Alviso) chipset consisting of:
- 82915GM Graphics/Memory Controller Hub (GMCH) with
Intel® Graphics Media Accelerator (GMA) 900
- 82801FB I/O Controller Hub (ICH6)
- 82802 Firmware Hub (FWH)
|
|
Memory
|
Dual 200-pin SO-DIMM socket, DDR2 533 (PC2) SDRAM, 2 x 1GB maximum,
symmetric dual channel capable
|
|
Video I/O
|
2 x DVI single or dual screen video output, up to 2048x1536 mode support,
graphics controller with dual independent display pipes for different display
timing and data on both outputs in single display mode, or dual screen mode for
higher resolutions and refresh rates
-
The lower DVI-I connector is suitable for both digital (DVI) and analog (VGA)
displays, for attachment of VGA style monitors adapters and adapter cables are available
-
The upper DVI-D connector is suitable for displays with DVI input only
-
Front panel option: D-Sub (female HD15) VGA connector available, replaces DVI-I connector
-
Rear I/O option: Analog video across J4/P4 suitable for CDT-RIO rear I/O
transition module (VGA connector)
|
|
USB I/O
|
All ports over-current protected, data transfer rate of up to 480Mbps,
conforming to USB2.0:
- 2 x USB type A connector (front panel)
- 4 x USB rear I/O ports across J4/P4
-
Suitable CDT-RIO rear I/O transition module provides 3 x USB back panel
connectors + 1 x USB on-board connector
-
2 x USB ports available with proprietary expansion interface option
(CCA-LAMBADA/CCB-BOSSANOVA mezzanine companion board)
|
|
Ethernet I/O
|
- Triple 10/100/1000Mbps Gigabit Ethernet (GbE) controller
- One GbE Port software switchable (BIOS) between front panel and rear I/O
- Up to 2 x GbE accessible via RJ45 jacks from the front panel
- 3 x GbE via front panel (option) by means of special mezzanine PCB C24-GBE (replaces 2nd DVI)
- Up to 2 x GbE rear I/O according to PICMG® 2.16 across J3
- Up to 2 x GbE rear I/O alternatively accessible via RJ45 jacks from the CDT-RIO back panel
- Jumbo Frame support up to 9KB
|
|
Serial Port (COM)
|
Available as an option, D-Sub 9-pin replaces DVI-D connector,
RS-232E or RS-485 selectable
|
|
Mezzanine Facility
PMC Module
or
SATA Storage Module
|
Optional usage of either:
-
1 Slot for a PMC module, I/O from the front panel and across J5,
dedicated PCIe to PCI bridge
- On-board Serial ATA dual 2.5-inch hard disk module C14-SATA
|
|
Proprietary Expansion Interface
|
- On-board LPC/USB/AC97 Super-I/O, USB and audio interface connector
- Suitable CCA-LAMBADA/CCB-BOSSANOVA mezzanine companion boards available
|
|
Parallel ATA (IDE)
|
Single channel IDE I/F (2 devices):
- Ultra ATA/100 connector, handover to CCA-LAMBADA/CCB-BOSSANOVA mezzanine expansion
board with optional on-board 2.5-inch hard disk drive or external device
- CompactFlash socket for a CFA ATA memory card or Microdrive® (C10-1-CFA)
- Option 1.8-inch on-board hard disk module C30-PATA (SSD available as an alternative), replaces CompactFlash facility
|
|
SATA (Serial ATA)
|
Quad-channel Serial ATA I/F:
-
On-board SATA mezzanine storage module option (C14-SATA),
1 or 2 hard disk drives 2.5-inch (mass storage module option
requires PMC slot space)
-
2/4 x SATA channels available for J3/P3 rear I/O option
-
Suitable rear I/O transition module CDT-RIO provides 3 x on-board SATA
connectors and optionally 1 x eSATA connector (back panel External SATA)
|
|
CompactPCI
|
ICH6 integrated 32-bit PCI bridge, 133MBps CPCI master
|
|
Rear I/O
J3/P3..J5/P5
|
- 4 x Serial ATA (SATA)
- 2 x GB Ethernet
- 4 x USB
- VGA Analog Video
- PS/2 Keyboard, Mouse
- COM1 (TTL Level)
- GPIO (TTL Level)
- AC '97 Audio
- Suitable rear I/O transition modules CDT-RIO available
|
|
BIOS
|
- Phoenix BIOS with EKF embedded systems enhancements
- 8Mbit Flash memory
- 8Mbit Flash memory
|
|
Drivers
|
- Intel graphics drivers
- Intel networking drivers
|
|
Typical Power Requirements
|
Board
|
+3.3V +0.17V/-0.1V
|
+5V +0.25V/-0.15V
|
|
CD3-2-JIVE
|
|
|
|
CD3-3-JIVE
|
|
|
|
CD3-6-JIVE
|
|
|
Thermal Conditions
Environmental Conditions
|
- Operating temperature: 0°C ... +60°C
- Storage temperature: -40°C ... +85°C, max. gradient 5°C/min
- Humidity 5% ... 95% non condensing
- Altitude -300m ... +3000m
- Shock 15g 0.33ms, 6g 6ms
- Vibration 1g 5-2000Hz
|
|
EC Regulations
|
- EN55022, EN55024, EN60950-1 (UL60950-1/IEC60950-1)
- 2002/95/EC (RoHS)
|
|
MTBF
|
tbd
|
Typical Performance Rating
Measured with PCMark2002 under Windows XP, 1GB DDR2 533
|
Board
|
Processor
|
CPU/MEM Score
|
|
CD3-2-JIVE
|
1.0GHz ULV Celeron® M (Dothan 373)
|
tbd
|
|
CD3-3-JIVE
|
1.4GHz LV Pentium® M (Dothan 738)
|
tbd
|
|
CD3-6-JIVE
|
2.0GHz Pentium® M (Dothan 760)
|
tbd
|
subject to changes
C14-SATA Dual Serial ATA Hard Disk Drive Mezzanine Module (Option)
|
CD3-JIVE with PMC Module
|
CD3-JIVE with PMC Module, C14-SATA, C24-GBE, CCB-BOSSANOVA Side Board
|
The CD3-JIVE comes with a CompactFlash adapter module (C10-1-CFA), which is suitable to
hold a silicon memory CF card or Microdrive hard disk. If the CD3-JIVE is
accompanied by a mezzanine expansion module such as the CCA-LAMBADA or
CCB-BOSSANOVA, the position of the CompactFlash adapter module changes to
the mezzanine card.
|
|
Optionally an on-board 1.8-inch hard disk module is available (C30-PATA). When ordered,
it replaces the CompactFlash adapter module (please request for a special
solution which allows to use both the CF slot and the 1.8-inch drive
simultaneously).
|
C10-1-CFA CompactFlash Adapter for CD3-JIVE (Included with CD3-JIVE, w/o CF-Card)
|
C30-PATA 1.8-Inch Hard Disk (or SSD) Module (Option for CD3-JIVE)
|
In addition, the CD3-JIVE can be optionally ordered with a 2.5-inch SATA hard
disk mezzanine module (C14-SATA, single or dual drive). This storage module option would
occupy the mounting space which was originally reserved for the PMC module.
If the CD3-JIVE is equipped with the C14-SATA storage module, the number of SATA
channels for rear I/O usage is limited to 2.
|
|
While the 2.5-inch hard disk module is an economical solution using the
CD3-JIVE on-board SATA controller, there is also a PMC based alternative
available - the DE2-TIGER,
a SATA/IDE controller PMC card with an integrated
1.8-inch drive. Both storage solutions can be used in parallel with the C10-CFA
CompactFlash drive or 1.8-inch hard disk option described above.
|
|
CD3-JIVE Block Diagram (1/2)
|
|
CD3-JIVE Block Diagram (2/2)
|
|
CDT-RIO Block Diagram
|
|
CD3-JIVE Assembly Drawing
|
|
CDT-RIO Assembly Drawing
|
|
Ordering Information |
|
Alias
|
Ordering No.
|
Short Description
|
|
JIVE
|
CD3-2-JIVE
|
6U/4HP CPCI CPU Board, 1.0GHz ULV Celeron® M (Dothan 373), 512MB DDR2 SDRAM
|
|
JIVE
|
CD3-3-JIVE
|
Similar to CD3-2-JIVE, 1.4GHz LV Pentium® M (Dothan 738)
|
|
JIVE
|
CD3-6-JIVE
|
Similar to CD3-2-JIVE, 2.0GHz Pentium® M (Dothan 760)
|
|
JIVE
|
CD3-Z1-JIVE
|
Option 1GB DDR SDRAM option (replaces 512MB memory module)
|
|
JIVE
|
CD3-Z2-JIVE
|
Option 2 x 1GB DDR SDRAM option (replaces 512MB memory module)
|
|
GBE
|
C24-GBE
|
Third Gigabit Ethernet front panel jack (replaces either secondary DVI Video connector, or requires 8HP board width)
|
|
SATA
|
C14-SATA
|
2.5-inch SATA hard disk mezzanine storage module, single or dual drive (occupies PMC module space, or requires 8HP board width)
|
|
PATA
|
C30-PATA
|
1.8-inch IDE hard disk drive module or SSD (replacement for CompactFlash socket C10-1-CFA)
|
|
LAMBADA
|
CCA-1-LAMBADA
|
3U CompactPCI Super-I/O module, local expansion board complementing the
CD3-JIVE, front panel width 4HP,
with keyboard/mouse, RS-232, optional audio connectors
& AC'97 Codec, mounting on top or bottom of the CD3-JIVE
|
|
BOSSANOVA
|
CCB-1-BOSSANOVA
|
3U Super-I/O module, local expansion board complementing the CD3-JIVE,
front panel width 4HP, 2 x USB, 1 x RS-232, PS/2 MS/KB,
mounting on top or bottom of the CD3-JIVE
|
|
BOSSANOVA
|
CCB-2-BOSSANOVA
|
3U Super-I/O module, local expansion board complementing the CD3-JIVE,
front panel width 4HP, 2 x RS-232, PS/2 MS/KB,
mounting on top or bottom of the CD3-JIVE
|
|
RIO
|
CDT-1-RIO
|
Rear I/O transition module for CD3-JIVE
|
|
TIGER
|
DE2-TIGER
|
PMC Card SATA/IDE Controller with 1.8-inch hard disk drive
|
|
